UE1

 

  • Product Description
  • Specification
  • Application
  • Diagram
  • Manual
  • Training Videos

Airofog electrically driven ULV cold foggers are profession applicators for applying disinfectants, biocides, insecticides or for humidification for both indoor and outdoor use. The fogger incorporates a maintenance-free encapsulated powerful electric motor blower which is corrosion-resistant, means that it is ideally suited for the application of aggressive chemicals, such as acid-based solutions applied indoors. The fogger is also equipped with a controller that allows for it to be pre-programmed for automatic operation. This improves safety by allowing fogging applications to be made without the presence of an operator and reduce chemical use in addition to reducing operating cost. Flow rate is easily visualized and can be regulated by the equipped regulator controller.

UE-1 TOP have rotational spray heads, which automatically rotate 360° to achieve an excellent distribution of fog. An agitator unit fitted inside the solution tank also avoids the build-up of sediment, so it is ideal for use with wettable powders.


UE-1 / UE-1 TOP

Motor Blower

encapsulated, maintenance free and corrosion-resistant

electric motor:

4 kW, 346-415- VAC, and 3-phase

protection:

integrated thermo contact

rated current:

10 Ampere

speed:

2780 min.

discharge

3.6 m3 /min.

pressure:

0.2 bar

air velocity at the nozzle:

180 m/sec.

air filter

paper star filter

Solution System

made of corrosion-rsistant materials (stainelss steel, Viton™, PE, PA, etc)

solution tank:

stainless stell AISI 304, 50 liters with lever indicator

solution filling height:

1 m

flow rate control:

manual regulator control with meter

flow rate varible:

0-18 litre/hr

aerosol spray head:

1 nozzle

spray nozzle:

double turbine type

Control

programming control for simple automatic operation

start:

selected stand-by time, self-running

fogging:

selected duration

post-blowing:

automatically blowing after completion of fogging for an optional air circulation and droplet distribution

stop:

automatically after post-blowing

△agitator

agitator blade moving forwards and backwards intermittently
avoid sentiment when applying wettable powder
always give better, more homogeneous mixture of substances

△rotation

automatically rotating 360, achieving excellent distribution

Chassis

stainless steel AISI 304, one-piece type

size (length x width x height):

50 x 68 x 126 cm

wheel:

2 pneumatic wheels, 2 steering rollers

Noise Level

electric drive, low noise level

measured at chassis handrail:

<85 dB(A)

Net Weight

~70 kg


Airofog USA ULV Aerosol Generator UE-1 Electrically driven

ULV Aerosol Generator UE-1 Electrically driven ULV Cold Fogger

Airofog electrically driven ULV cold foggers are professional applicators of applying disinfectants, biocides, insecticides or for humidification for both indoor and outdoor use.

It is particularly important for indoor use that the fogger incorporates a powerful electric motor blower which is encapsulated, maintenance free and corrosion resistant and is ideally suited for the application of aggressive chemicals such as acid based solutions applied indoors. The fogger is also equipped with a controller that allows it to be operated by pre-programming for automatic operation. This improves safety by allowing fogging applications to be made without the presence of an operator and reduce chemical use and operating cost. Flow rate is easily visualized and can be regulated by the equipped regulator controller.

UE-1 TOP and UE-2 TOP have rotational spray heads which automatically rotate 3600 to achieve an excellent distribution of fog. An agitator unit fitted inside the solution tank also avoids build up of sediment so ideal for use with wettable powders.

The Airofog ULV Aerosol Generator UE-1 is driven by a electric motor blower which is encapsulated, maintenance free and corrosion-resistant. This machine applies to both outdoor and indoor, especially extraordinary when applying acid based solution in an enclosed space as motor and blower will not be damaged. By programming control for self-running programme, it can be operated automatically, which helps lowering labor cost and reducing operator’s exposure to chemicals.

The air compressor operates on the principle of the side channel blower and is matched to the solution nozzle well. It produces a comparatively small air throughput at a high compression ratio, which is advantageous considering the narrow nozzle bores.

The solution nozzle works in two stages.

The first step breaks up the liquid at a high velocity (about 180m/sec.). At the end of a short conical diffuser, compressed air enters again which is acting in an opposite direction and provides a better break up of the droplets. The stream of droplet is dispersed without touching the inner surface of the solution nozzle. Thus wettable powder suspensions can be applied without the danger of blocking nozzle.

The control of the throughput is due to a needle flow regulator from 0 to max. appr. 24 l/h depending on the type and viscosity level of the liquid to be fogged.


Application hints

All parts exposed to the chemical solution are made from corrosion-resistant materials (stainless steel, brass, PE and etc.). Thus, all approved chemical solutions that don’t attack these materials can be used without restrictions. No damaging influences of licensed pesticides are known.

Fogging mixture

The chemical preparation is to be mixed with clean water as a carrier. A water temperature of 20-300C supports the mixability with the chemical preparation and is of advantage to achieve a constant output and a homogeneous droplet spectrum.

To reduce the high evaporation rate of the fine aerosol droplets when water only is used as a carrier, special organic carriers like glycol, polyethyleneglycol, Nevocol or emulsifiable white oils should be added. A quantity of 5-10% of the total carrier quantity is sufficient to manifold the durability of the fine aerosol droplets. This is especially important when the relative air humidity is considerably below 90%.

The total mixture (=chemical preparation + water) should never be less than 1L per 1000m2 for plant protection or per 1000 m3 for other space treatments. A quantity of water of e.g. 2-3L per 1000m2 resp. 1000 m3 or even higher is of advantage, since more droplets of constant quality are formed and a better coverage is obtained.

In practice the following mixing ratios proved successful as a guide line:
            powder formulations / water        1:15 to 1:25
            liquid formulations / water            1:10 to 1:20


NOTE!: Observe applicable laws when selecting active solution and/or carriers.


The above are based on international application methods and experiences. Since correct application is beyond our control, we cannot be held responsible for ineffective treatment and damages caused by unsuitable chemical preparations or by incorrect application.



Airofog USA ULV Aerosol Generator UE-1 Diagram & Part List




Click to Download Diagram & Part List - PDF


Airofog USA ULV Aerosol Generator UE-1 Part List

1. operator box 7. telescopic pole
2. chassis 8. spray nozzle
3. motor blower 9. flow regulator
4. air filter 10. type plate
5. power supply box 11. solution tank pressure gauge
6. solution tank 12. solution valve


Airofog USA ULV Aerosol Generator UE-1 Manual & Schematic

Click to Download ULV Aerosol Generator UE-1 Manual - PDF


Airofog USA ULV Aerosol Generator UE-1 Manual


BACK
AIROFOG – “Professionals Choice” for value, reliability and performance